Three Phase 220V 380V Output 75Kw 150A Solar Pump Drive With Mppt Function For Agriculture And Forestry Irrigation
ZK Solar Pump Inverter Features
1.In-built MPPT and efficiency up to 99.6%
2.20 kinds of protection level.
3.Save energy costs and maximize productivity.
4.The drives can be equipped with remote monitoring options, reducing maintenance trips to the site.
5.Configuring. end user ,who never used inverter before, can Install and operation it very well.
6.Easy install and operation and little parameterEmbedded pump-specific features such as dry run detection,minimum power input protection,
maximum current protection,stop frequency running protection.
Technical Specification
| Recommended MPPT voltage range | Vmpp 131 to 350 VDC for 1S (80V to 350VDC input, 3PH 110 to 220VAC output)
Vmpp 280 to 375VDC for 2T ( 150V to 350VDC input, 3PH 220 to 240VAC output)
Vmpp 486 to 800 VDC for 4T ( 250V to 900VDC input, 3PH 380 to 460VAC output) |
| Recommended input voltage (Voc and Vmmp) | Voc 180(VDC), Vmpp 155(VDC) for 1S model or 110V AC pumps
Voc 355(VDC), Vmpp 310(VDC) for 2T model or 220V AC pumps
Voc 620(VDC), Vmpp 540(VDC) for 4T model or 380V AC pump |
| Motor type | Control for permanent magnet servo motor and asynchronous motor pumps. |
| Input power | DC power from solar arrays or AC grid power |
| Maximum DC power input | 450VDC for 220-240VAC output /900VDC for 380-460VAC output |
| Rated output voltage | 3-phase , 110V/160V/220V. 3-phase, 220V/240V/380V/460V/480V |
| Output frequency range | 0~50/60Hz |
| MPPT efficiency | 97%, |
| Ambient temperature range | (G-type inverter with submersible pumps, and P type for general pumps. |
| Solar pump control special performance | MPPT ( maximum power point tracking), CVT (constant voltage tracking), auto/manual operation,
dry run protection, low stop frequency protection, minimum power input, motor maximum
current protection, flow calculating, energy generated calculating |
| Protection function | Phase loss protection, phase short circuit protection , ground to phase circuit protection , input
and output short circuit protection. Stall protection |
| Protection degree | IP20, Air force cooling |
| Running mode | MPPT , CVT, variable frequency mode |
| Altitude | Below 1000m; above 1000m, derated 1% for every additional 100m. |
Wiring description:
It is accepted dual power AC/DC mode connecting input.
User can able to install a power switchover to selection which mode power input as conditions.
Wiring P+ and P- of DC solar power to R, T terminals, or 1/3 phase cables of AC power supply to R, T ( R, S, T) of inverter. Connect 1 phase 220VAC AC input L, N to R and T terminals of inverter.
Built a Run/Stop switch S1 to start pumping when setting P0.02 for 1,that inverter works in terminals control mode. This inverter can achieve auto start at morning when sun light radiation is good, auto stop when sunset when sunlight radiation is low.
Built a switch 2 to disable solar pump control mode when connecting AC grid input. The inverter can be used for a variable speed drive (VFD) for pumps speed adjusting as need The output frequency can be adjusted by P0-03 frequency reference mode setting. The MPPT function is closed when turn off switch 2 and set P4.02=53. The solar pump control mode function also can be disable by parameters setting PE00=0
.
Connect 2 wires of float ball sensor to DI4 and COM for water tank level fulling detecting, and set P4.03=51( float ball NO relay alarm). When water level reached to sensor detecting, the normal open (NO) relay point will be activated, inveretr stop pumping, and sent a A.FuL alarm.
Connect 2 wires of sensor of dry run sensor of well to DI5 and GND, and set F4.04=52 ( dry run NC relay alarm). It will sent alarm A.LLd and stop pumping when lack of water in well for dry run protection.
Product Tags:
|
|
150A 75Kw MPPT VFD Solar Pump Inverter For Agriculture Forestry Irrigation Images
|
